Kitchen Cupboard Set up – Step-By-Phase Instructions on How to Put in Kitchen area Cupboards Your self

Now that you have your new kitchen area cabinets, you are prepared to move on to the subsequent massive action…..Setting up your kitchen area cupboards. Although the actual set up of the Kitchen Cabinets isn’tall that tough, the crucial 1st stage is measuring and marking out where the cabinets will go. By placing format markings on the partitions and floors, it will not only help you with kitchen cabinet placement and stud spots, but it will also aid you identify exactly where changes and shims will be required. Just before we get started there are a couple of items that you will require for the task:


Stage or Laser Level


Tape Measure

Stud Finder


one” x three” Piece of lumber (6′-8′ in size) or an Inverted U-formed frame (see notes beneath)


Screws (lengthy enough to go one one/two into the studs)

Utility knife or chisel

Marking Compass

An added established of arms (you could have to bribe one of your close friends)

As I pointed out above, you have the selection of making use of a piece of 1′ x 3′ lumber for the installation or creating a frame to help the cupboards (I have included a photograph of a sample body below). This can be made out of 2′ x 4’s and need to be tall adequate to assist the base of your wall cabinets. If you strategy on installing far more than one particular kitchen area, then I would suggest the frame, but a piece of lumber will do just good if this is a one particular time function. In possibly case, you will want yet another set of arms to assist with the installation.

In this case we purchased (RTA) Prepared-To-Assemble Kitchen area Cabinets from RTA Kitchen & Bathroom Cupboard Retailer. Now the kitchen area cabinets are assembled, we are all set to commence marking out our format lines. Some people start with the base cupboards, but we are likely to commence with the wall cupboards 1st. There is no proper or wrong way to begin, I just desire to begin with the higher cupboards first.

one. Use a degree and a pencil to attract a parallel line across the wall about three inches up from the ground. Measure down from this line, to the flooring, and uncover the flooring substantial stage (if it has one), and mark a line at that level. From that substantial level, Evaluate up 34 one/2 inches and draw a degree line throughout the wall to designate the leading of the foundation cabinets.

two. Now that you have the leading of the foundation cupboards marked, measure up an additional 19 1/2 inches and a stage line across the wall to reveal the bottom of the wall cupboards. Lightly mark every cabinets’ proportions and placement on the wall to make positive that your original format is appropriate.

three. Use a stud finder to locate the wall studs. Use a pencil to mark the stud spots at minimum 6 inches previously mentioned and under the line for the bottom of the wall cupboards. Attract straight vertical strains amongst the top and base marks to point out the center of the studs.

four. If you made a decision to go with the piece of 1′ x 3′ lumber, now is in which you will use (if you made the decision to go with the U-formed body, it will occur into engage in soon after all your lines are laid out). Screw a temporary 1′ x 3′ help rail to the wall, aligning the best edge of the rail with the line for the base edge of the wall cabinets. Attach it by driving 3 or 4 two inch screws by way of the rail into the wall studs.

5. Now that we have all the lines marked, it is time to start setting up your kitchen cabinets. Trinity Home Center are going to begin with the corner cabinet (below is exactly where your helper’s added set of palms will be needed). Area the corner cupboard on to the short-term support rail and have your helper maintain the corner cupboard in spot. Drill pilot holes by means of the sturdy cabinet again or its assist rail and into the wall studs. Screw the cabinet into the wall utilizing two screws that are lengthy sufficient to penetrate the studs by at the very least one one/two inches. Check out the leading of the cupboard for degree and the front of the cupboard for plumb. If you have to right the position, just again the screws out a little little bit and leading shims behind the cabinet at the stud places. If it is plumb and amount, push the screws all the way in and add a number of a lot more into each and every stud to guarantee that the cupboard is secured tightly to the wall.

6. Now we are likely to go onto the cupboards on either facet of the corner cabinet. As you put in every 1, use the clamps to secure each and every cabinet to the neighboring cupboard and then check out it for plumb with your stage. On faceframe cupboards, it is a good thought to drill two one/8 inch pilot holes by way of the sides of the faceframe and use screws. In this circumstance, with frameless, completely ready-to-assemble kitchen area cupboards we are going to screw by means of the plywood sides and use shims in in between the cabinets to make certain a tight suit and make confident that the cabinet faces are plumb.

seven. Following all the wall cabinets are in area, set up the corner or finish foundation scenario cabinet. Use shims exactly where required to degree the cabinet and increase it up to the line which signifies the high point of the floor. Be confident it is level from front to again and from aspect to facet, then screw it to the wall studs. If you don’t have a diagonal corner cabinet or blind foundation cabinet in the corner, thrust the adjoining cupboard into place and clamp the two units together. Incorporate a filler strip if necessary to enable the doorways and drawers sufficient clearance to open and shut effectively. If necessary, tap shims below the cupboard and behind it to modify for plumb and degree.

8. Push screws through the cabinet again (and shims) into the wall studs. Trim any surplus material from the shims with a sharp chisel or knife. Carry on to incorporate adjoining cabinets in this method, joining them the identical way you linked the wall cabinets in step 6.

9. If your cabinets finish up butting from one more wall, you might need a filler strip to make up the final few inches. If you have customized cupboards, they need to have been created to fill this hole, but if you are employing inventory or RTA Kitchen Cabinets the filler strip may be essential. If you do want to use a filler strip, go away the final cabinet detached from the other cabinets. Clamp a straightedge to the experience of the closest installed unit, extending much ample for you to put alignment marks on the stop wall. Enable a three/4″ offset behind individuals marks (for the thickness of the filler piece) and fasten a cleat to the wall. Then install and fasten the very last cabinet and evaluate the hole among its experience body and the wall.

If the wall is flat, just rip the filler board to the required width and fasten it in location. If the wall is irregular, you may have to scribe-fit the filler board. Start by setting a marking compass to the width of the gap, then spot a strip of 1″-wide masking tape along the filler board in the region exactly where it demands to be trimmed. Clamp the board to the stop cabinet’s experience body, then trace the wall contour with the compass. Take away the board and lower together the scribe line with a jig observed, then reinstall it to examine the suit. When it’s right, drive screws via the adjacent encounter body into the edge of the filler board. Screw or nail the other facet to the cleat.

At this stage, your kitchen area cabinet installation is comprehensive. If you acquired matching crown molding or any other details, these ought to be effortlessly set up now. Dependent on whether or not you had to use shims underneath the base cabinets, you could have to set up some trim parts by the toe kicks to go over up the shims or any gaps at the base of the kitchen cupboards.

I hope this helps make your kitchen area cupboard installation as clean as possible. If you want any assist with cupboard assortment, kitchen area structure guidelines, or suggestions for cupboard variations, examine out RTA Kitchen area & Toilet Cabinet Retailer